CutCat Pro tool · 3D preview free · files need a pass
Laser cut Money Box generator
Pick the savings goal, the smallest amount and a caption. Every square on the front gets its own number, all of them add up to exactly your goal. Check the box in 3D, then download a cut-ready SVG or DXF. Joints and kerf are already worked out.
Vector: Give me a goal. I'll number the squares. Cut: And I'll check every sum.
- Outside
- —
- Squares
- —
- Sheet
- —
- Goal
- —
The 3D view and the cut sheet are free to try. The cut files are Pro: see CutCat Pro.
How to use it
- Type your savings goal and pick the smallest amount a square may hold.
- Add a caption, set your sheet thickness and kerf.
- Turn the box in 3D, shuffle the numbers if you like another arrangement, then download the SVG.
Putting it together
Dry-fit everything first, then glue.
- Cut one sheet. Red lines are cuts, blue is the engraving of the numbers and the caption, green is the score lines of the grid.
- Slide the four walls together: the top wall (with the coin slot) and the bottom wall (with the round hole for the lock) go between the two side walls.
- Round box: put the bottom wall (with the lock hole or the plate window) on the back panel, tabs in the slots. Then bend the two flexible strips round the circle, one from each end of the bottom wall up to the top: their tabs go into the curved slots. At the top the two flat ends meet in the middle of the coin slot. Put a drop of glue where the strips meet the bottom wall.
- Stand the walls on the back panel, tabs in the slots: the top wall (with the coin slot) and the bottom wall (with the lock hole), then the others between them. Every wall runs to the outer corner and the next one starts a little later, so the corners meet without overlapping: put a drop of glue on each corner.
- Fit the front and back panels on the tabs of the walls. The numbers face out.
- Glue the frame over the front panel so the squares show through its window.
- Pen holder: from inside the box push the tray and the ring (the plate with the hole) through the two wide slots of the side wall, body first: the wider head stays inside and holds the plate. Glue them, then glue the rim ring (the plate with a hole) on the tray, against the wall. The pen stands in the rim and in the ring.
- Photo pocket: the long rear tabs of the side and bottom walls go through the back panel into the slots of the U-shaped pocket frame. Glue the decorative frame over it, then slide your photo into the pocket from the top.
- Put the lock together: the washer with ears goes into the bottom hole, then the washer, the wing nut and the pin through all the holes.
FAQ
Do the numbers really add up to my goal?
Yes. The squares are chosen so their sum is exactly the goal, and the page shows the sum under the preview.
What is free and what needs CutCat Pro?
The 3D view, the cut sheet and the small fit test strip are free to try. The cut files (SVG and DXF) need a CutCat Pro pass: sign in on this site and the page asks our server to make the file for you.
Do I need an account?
Only to download the cut files. The preview is calculated in your browser. For a file, the page sends your box settings (sizes, goal, caption, thickness, kerf) to our server and gets the file back; nothing else is sent and nothing is stored.
Which format should I choose?
SVG for LightBurn, xTool and Glowforge. DXF for CAD programs and older laser software. Red is cut, blue is engraving, green is the light score of the grid. In both files engraving comes first and the cut last, inside shapes before the outlines.
Should I turn on kerf offset in my laser software?
No. Kerf is already built into the file: set your kerf in Advanced settings and leave kerf offset off in your software, or the joints will come out loose.
Which plywood thickness can I use?
3 mm or 4 mm plywood. Cut the small fit test strip first to check that your tabs and slots fit.
Why is the sheet bigger than a small laser?
The classic box sits on one sheet of about 402 × 312 mm. Pick your own sheet or work area in Advanced settings; the page warns you before you save if the parts do not fit.
Which lock should I choose?
The wing nut lock turns on a pin through the bottom wall. The sliding plate lock is a plate you pull out of the bottom: click it in the 3D view to open and close it.
Can I make a round or a hexagon box?
Yes. Choose the shape under Size: rectangle, hexagon or round. The round box has a flexible wall or flat panels.
What photo size can I use in the photo pocket?
Any size from 80 mm to 260 mm on each side, horizontal or vertical. The box is built around your photo, and the window of the decorative frame covers 2 mm of every edge, so the edges never show.
Can I add a glass in front of the photo?
Yes. Enter the glass thickness: the rear tabs get longer by that amount, and the glass stands on them between the pocket frame and the decorative frame. The page shows the glass size to order.
Can I use a savings challenge instead of a goal?
Yes. Choose the 52 weeks or the 100 envelopes challenge and the squares are numbered for it.
Can I change the goal and the amounts in the squares?
Yes. Type any goal and pick the smallest amount a square may hold: 1, 2, 5, 10, 20, 25, 50 or 100. The squares are filled so that their sum is exactly the goal. In the same section you can mix big and small amounts, make them even or sort them from small to large.
Can I put the currency in the caption?
Yes. Pick the currency symbol or none: it goes into the numbers and the goal line under the caption (for example GOAL $10,000). Tick or untick the goal line as you like.
Can I write my own caption?
Yes. Type your own text or pick one of the ready captions in the list (MY FIRST CAR, NEW GUITAR, SUMMER CAMP and more). The caption is engraved over the grid. It uses Latin letters, digits and common signs; other alphabets are not in the font.
Why do I need the sheet thickness and the kerf?
The tabs and slots are drawn for your plywood. Thickness sets their depth, and kerf (the width of the laser cut) sets how tight they are. Measure your kerf with the free kerf test and enter it in Advanced settings.
What if the box feels too tight or too loose?
Use the fit setting in Advanced settings: Tight makes every slot a little narrower, Loose a little wider. The free fit test strip lets you check it before you cut the whole box.
How does the lock work?
The wing nut lock is made of four small parts that stack on a pin through the bottom wall. Turn the wing nut and the lock opens, so you can take the coins out. The sliding plate lock is a plate on the bottom that you pull out through the side.
Can I get my coins back out?
Yes, through the lock in the bottom. The coin slot in the top wall is for putting money in.
Can I engrave the numbers instead of scoring them?
Yes. Under “Numbers and text” choose Engrave (filled, the blue layer) or Quick cut (outlines, the green layer, faster to burn).
Can I add a pen holder?
Yes. Switch on the pen holder and pick the side. Two T-shaped plates go through the side wall from inside and hold a pen in the ring.
How do I put the box together?
Under the generator, “Putting it together” lists the steps for your box. Dry-fit everything before you glue. Every part has a number: tick “Part numbers” to see the same numbers in the 3D view and on the cut sheet.
Will my box look like the one in the preview?
Yes. The 3D view is built from the same parts as the files. Turn the box with the mouse, use Pull apart to see how it goes together, and click the sliding plate to open it.
Can I sell boxes I make?
Yes, with a CutCat Pro pass you may sell the money boxes you cut. You may not resell the files themselves.