Free · top-down video rig from plywood

Overhead phone stand generator

Tell it what you film. It sets the height so the whole thing is in the shot, keeps the legs out of the picture and gives you a knock-down stand to cut.

Vector, a curious cat

Vector: Pick what goes under the camera. I'll work out the height. Cut: And I'll check that the parts fit your sheet.

Video
Camera on your phone
What you film
Span between uprights
Material thickness
Base
Hanging boxes
Shelf position
Drag to rotate · right-drag to move · scroll to zoom
what the phone sees, about

The files have two layers by colour: red slots and holes, green outlines. Cut the red lines first and the green outlines last, and check the order in your software preview. Cut one upright and the shelf first and try the fit before you cut the rest.

How to use it

  1. Choose vertical or horizontal video and what you film: a sheet, a cutting mat or your own size.
  2. Pick your material thickness. In Advanced settings enter the thickness you measured, your kerf and your sheet size.
  3. Each upright has ten height slots: move the shelf down a slot for close-ups.
  4. Check the sheet size, download SVG, DXF or LightBurn files and cut. Red lines first, green outlines last.

Putting it together

  • Press the stiffening ribs into the shelf and into the two uprights. A drop of glue makes them permanent; the rest stays knock-down.
  • Slide the feet onto the uprights, push the shelf tongues through the slots at the height you want and tap the wedges in.
  • Storage boxes: push the two side walls into the floor slots, drop the outer wall onto them, drop the two dividers into their slots, then lower the upright onto the side walls. The floor sits against the upright.
  • Hanging boxes: slide the two hooked sides onto the floor tabs, drop the two end walls onto them (flex the wall a little so the floor tab snaps into its hole), then hang the box by its hooks in a pair of hook slots.
  • Adding light? Stick the LED strip under the shelf, run the wire down the inside of an upright next to its edge. Each zip tie goes in through a small hole from the outside, round the wire, round the edge of the upright and locks outside.
  • Fit the runners and the side lips to the phone platform, set it on the shelf and lay the phone with its camera over the cut-out.

FAQ

Will thin plywood hold a phone?

Yes. The shelf and the uprights have ribs that stop them from bending, so the stand works from thin sheet. The design is new: cut a test set and check it with your own phone before you rely on it.

Does it fit my phone?

The platform is sized for the largest current phones in a case. Pick where the camera sits on your phone: in the corner, in the centre or as a bar across. The camera hangs over an open cut-out, so there is no window to match.

How exact is the picture size?

It is an estimate for the main camera in video mode. Phones differ a little, so check the shot once before filming.

Which files do I get?

SVG, DXF and LightBurn files, laid out on sheets of the size you pick. If the parts need more than one sheet, you get a zip with one file per sheet.

What thickness can I use?

Plywood or MDF from 2.5 mm to 6.5 mm. Enter the thickness you measured in Advanced settings and every slot follows it.

Why do I need the kerf?

The laser burns away a thin line of wood. With the kerf entered, the slots come out at the size they should be, so the stand is neither loose nor too tight. Measure it with the Kerf test.

The parts are too tight or too loose. What do I change?

Change the fit clearance in Advanced settings. More clearance makes the slots wider and the stand easier to take apart. Cut one upright and the shelf first and try them.

What is the LightBurn file for?

It opens with the two layers already in the right order and with your own speed and power. Use File, Open in LightBurn. The settings are yours: the generator does not guess them.

Can I add light?

Yes. Each upright has small holes near both edges for zip ties, so a wire from an LED strip under the shelf runs down the inside of an upright. The buttons on the 3D view only show how it looks, the parts are the same.

Can I sell stands I make with it?

Yes, you can sell the stands you cut. Do not sell or share the files themselves.

Do I need glue?

Only for the ribs, if you want them permanent. The stand itself locks with two wedges and comes apart flat.