Pro · spinning prize wheel from plywood

Wheel of fortune generator

Pick the size, the plywood and the number of sectors. Spin the wheel in 3D and check how it goes together, then take the cut files with CutCat Pro.

Vector, a curious cat

Vector: Give the wheel a spin with the mouse. It stops by itself, like the real one. Cut: And I'll check that the parts fit your sheet.

Units
Material thickness
Form
Wheel size

The size is the width of the arch stand. The wheel with its ears is a little wider.

Sectors

One ear for every sector line. The score lines on the wheel follow the number of sectors.

Score lines

Engraved dashed lines on the wheel, from the hub to every ear.

Cap disc picture

The picture is engraved on the face of the cap disc. Fine details under 0.5 mm will not come out.

Drag the wheel to spin it · drag elsewhere to rotate · scroll to zoom
the arrow stays still, the wheel turns
CutCat Pro pass needed for the files.

The 3D view and the cut sheet are free to try. The cut files are Pro: see CutCat Pro.

How to use it

  1. Pick the size of the wheel: small, medium, large or your own size in between.
  2. Pick the plywood thickness. The slots and the wooden axle follow it.
  3. Choose how many sectors you want, from 4 to 24, and straight or spiral score lines. Every sector line has its own ear on the rim, which you use to spin the wheel by hand.
  4. Turn the model, pull it apart and check the sheet size. The cut files come with CutCat Pro.

Putting it together

  • Lock the two halves of the wooden axle into each other to make a cross.
  • For the tabletop and hand-held forms, push the cross through the cross-shaped slot from behind and slide the large rear disc onto it.
  • Slide the small bearing disc onto the cross and place the wheel over it. The wheel turns around the round outside of the bearing disc.
  • Put the second big hub disc on the front. Then glue the cap disc, the one without slots, on top of the axle. You can engrave a picture, a short text or your own logo on it.
  • The base plate has two tabs that push into the slots at the bottom of the arch.
  • The arrow has a neck that goes through the slot in the base plate, and its foot locks under the plate.
  • Give the wheel a flick by an ear. It turns on the axle and stops by friction, so there is no clicker.

FAQ

What is it?

A spinning prize wheel for a table: an arch stand holds a round wheel with sectors, and a fixed arrow shows where it stopped. You turn the wheel by hand using the ears on its rim.

What do I get for free?

The 3D view, the pull-apart view and the cut sheet with its layout and size check are free to try. The cut files are part of CutCat Pro.

Which sizes are there?

Three sizes from the original set, 150 mm, 215 mm and 300 mm, and any size in between. The size is the width of the arch stand.

What thickness can I use?

Use 3 mm or 4 mm plywood. The slots, the arrow and the wooden axle follow the thickness.

How many sectors can the wheel have?

Any number from 4 to 24. The ears on the rim and the score lines follow the number.

Why does the wheel have ears?

They are handles. You flick the wheel by an ear to spin it. The small round marks on the ears are engraved, not cut through.

Does the arrow click on the ears?

No. The wheel stops by friction on its wooden axle, and the arrow only points.

Why is the axle made of wood?

Two flat pieces lock into a cross and go through cross-shaped holes. They are cut from the same plywood as the rest, so you need nothing else to build it.

Can I put my own logo on the wheel?

Yes. The cap disc in the middle takes a picture, a short text or your logo. Load an SVG, PNG or JPG, then choose whether to send its traced outlines and set the threshold, and it is engraved on the disc. The file stays in your browser.

Do I need to measure my kerf?

It helps. The wheel has to turn freely on the axle but not wobble. The Kerf test gives you the number for your laser and your plywood.

Can I sell wheels I make with it?

Yes, you can sell the wheels you cut. Do not sell or share the files themselves.