Free tool · no sign-up · commercial use OK

Laser cut bottle box generator

Pick your bottle, set the material, check the case in 3D, then download a cut-ready SVG or DXF: a case with a front that slides up, a lid that slides out, an arch top with a handle, a gable roof with a handle plate, or an open top with a lattice.

Vector, a curious cat

Vector: A snug home for one good bottle. Pick it, I will measure round it. Cut: And slide the lid open with style.

Box style

Bottle

Opens by
Open top: walls
Neck holder
mm
mm
mm
mm

Size

mm
mm
mm

Material

mm

Measure it with calipers. Sheets are rarely exactly what the label says.

Dividers

Across the width
0
Across the depth
0
Drag to rotate · right-drag to move · scroll to zoom
Outside
—
Inside space
—
Sheet used
—
Cut time
—
Cut the cat, with a magnifier
Cut
Free, no email needed.

Need something fancier?Ready-made box designs: beer carriers with a handle, guitar pick boxes, planters and gift boxes, from $2.

How to put it together

The numbers are the same on the cut sheet and in the 3D view (tick "Part numbers"). Dry-fit everything first, then glue.

    How to use it

    1. Pick how the case opens, then choose your bottle: a preset (Bordeaux, Burgundy, champagne) or your own diameter and height. Measure the widest point of your bottle: the presets are typical sizes.
    2. Enter the thickness you measured. "Room round it" is the play on each side of the bottle, "Room above the bottle" is the space over the top.
    3. Turn the case in 3D, press "Pull apart" to see how it goes together, and pick the handle for the lid or panel.
    4. Download the SVG and open it in LightBurn, xTool Creative Space or the Glowforge app. Cut lines are red, at the true size. Cut one wall and the bottom first, and check the tabs before you cut the rest.

    The five ways to build it

    • Front slides up. The top is fixed and the front panel slides up between two guide frames. An optional neck holder keeps the bottle from rattling.
    • Lid slides out. A tube with a lid that slides out of the top between two frames and a rail. Good for a gift you open from above.
    • Arch top. The top of the front and the back bends in on slits and the two flat tops meet like a roof, with a window to carry it by. The bottle goes in from above before you close the arch.
    • Gable top. The front and the back bend into an S and meet face to face as one flat handle plate with a round hole. The handle plate has tabs on both edges. The two narrow walls lean in against it and end in a point with a slot: push the tabs through the slots, no glue.
    • Open top. A tube with no lid. Add handle slots in the front and the back, and a diamond lattice in the walls to carry the bottle and to see it.

    FAQ

    Will it fit my bottle?

    Type the diameter at the widest point and the height of your bottle. The presets are typical sizes only: bottles of one kind are not all the same size. The case is the bottle plus "Room round it" on each side, and "Room above the bottle" on top. With the two sliding styles the 5 mm guides narrow the opening, so the case is 10 mm wider than the bottle plus the room round it.

    Which style should I choose?

    "Front slides up" hides the bottle behind a panel and looks like a clean block. "Lid slides out" is the classic case with a lid. "Open top" is the quickest to cut and to assemble, and the lattice lets you see the bottle.

    What is the neck holder?

    It is a shelf with a keyhole notch, only for "Front slides up". It holds the neck of the bottle so the bottle does not move. It is off by default; switch it on if your bottle rattles.

    How does the arch bend?

    The top of the front and the back has rows of slits (a living hinge), so 3 to 4 mm plywood or MDF bends slowly inwards. Bend it by hand and keep the slits on the outside. If it cracks, make the slit pitch smaller; if it bends too easily, make it bigger. The two flat tops meet at the top and the windows line up into a handle. Test a spare strip first.

    How do the walls join?

    The two side walls are 5 mm bigger than the box on every side, with rounded corners. The front, the back and the bottom stand between them on tabs through slots 5 mm from the edge, so there are no joints on the corners.

    Can I choose the handle slots and the lattice?

    Yes, with "Open top". "Handle slots" puts a slot near the top of the front and the back; "Lattice" fills the walls with diamond cuts. Turn either off for plain walls.

    Which handle should I choose for the lid or the panel?

    "Glued rim" is a 5 mm strip glued round the edge; it is the default. "Finger hole" and "Oval slot" are cut out of the lid or the panel, and "Pull strip" is a strip you pull by. Choose the one that suits your hand and the look of the case.

    What material should I use?

    Plywood or MDF 3 to 6 mm thick. Measure your sheet and type the real thickness. The longest wall is a little longer than the bottle, so a Bordeaux bottle needs a sheet at least 400 mm on the short side.

    Can I sell cases made from these files?

    Yes. Files from this generator are free for personal and commercial use. You can sell the cases you make.

    Should I turn on kerf offset in my laser software?

    No. Kerf is already built into the file. Leave kerf offset off in LightBurn, xTool Creative Space or the Glowforge app, or the joints will come out loose.

    Do I need an account?

    No. Everything is calculated in your browser: your case is not uploaded or stored anywhere.

    Is there an assembly guide?

    Yes. Under the generator, "How to put it together" lists the steps for your case. Every part has a number: the same number is on the cut sheet and in the 3D view when you tick "Part numbers".

    What if the parts do not fit on one sheet?

    The generator adds more sheets. You then get a ZIP with one SVG or DXF file per sheet, so each file matches one piece of material.